← Back to Blog
November 5, 2026•By Bravio Team

Medical Equipment You Can't Find at PM Time: An Unable-to-Locate Procedure for Biomed Shops

medical equipment unable to locatecould not locate biomed PMunable to locate PM completionmissing medical equipment PMbiomed PM completion ratePM completion unable to locate policy

Short answer: treat "unable to locate" as a procedure, not a status. Search on more than one visit, ask the department and the customer's biomed contact in writing, log every attempt with the date, who you asked and where you looked, and escalate to the customer before the PM goes overdue. A device that is still missing after a documented search is reported to the customer as not performed, with the reason, and either stays on the next sweep or is retired from the inventory by the customer. What will not stand up is a stack of "unable to locate" entries made on the last day of the month.

Every shop doing PM contracts knows the pattern. The list says 40 infusion pumps on 4 West; the techs find 31. Some are in the clean utility room on another floor, some are in a patient room you cannot enter, a couple went out for OEM repair, and one was quietly retired two years ago and never taken off the list. How you handle those nine decides whether your PM completion report is believable.

Why it matters to your customer, and so to you

The hospital is surveyed on its equipment maintenance, and when you maintain the equipment, most of the evidence is your PM records. Before Joint Commission reorganised its standards into a Physical Environment chapter in 2026, the old hospital standard EC.02.04.03 expected 100% completion for high-risk equipment and for equipment maintained to manufacturers' recommendations; maintenance is still required and still surveyed under the new numbering (see what surveyors expect from the ISO that maintains a hospital's equipment).

HTM leaders have argued that "completion" does not have to mean "performed". In a widely shared MedWrench piece, Banner Health's Tony Cody listed cases he counts as complete, including a device that cannot be found after repeated, well-documented searches, while warning that documentation made only at the end of the month would probably not be accepted and that a high share of unperformed PMs would be unacceptable however it is categorised (MedWrench, 2019). That is one practitioner's interpretation, not a Joint Commission ruling, so agree the method with each customer in writing.

The unable-to-locate procedure (copy this)

  1. First pass. The technician checks the listed location, the department's equipment room, clean and soiled utility, and asks the charge nurse. Record: date, time, places checked, who was asked.
  2. Check the records. Is there an open repair work order, an OEM or depot repair, a loaner swap, or a transfer to another department? Check your own system and ask the customer's biomed or materials contact.
  3. Second pass on a different day. Ideally a different shift, because devices move with patients. Record it the same way.
  4. Written request to the customer. Email the department manager and your customer contact with the asset tag, serial number, model and last known location, and ask them to confirm whether it still exists. Keep the email on the work order.
  5. Escalate before the due date. Send your customer contact the list of unlocated devices while there is still time to find them, not with the month-end report.
  6. Close with a reason. If it is still missing, close the PM as not performed, reason "unable to locate", with the attempts attached, and carry the device onto the next PM sweep.
  7. Retire or reinstate. After an agreed number of missed cycles, ask the customer in writing to decide: retire it from the inventory (their decision, recorded), or keep looking.

What to record on each attempt

FieldExample
Asset tag, serial, modelBM-04512, SN 7781234, infusion pump model X
Listed location4 West, room 412
Date and time of searchNov 3, 10:40
Places checked4 West clean utility, equipment room, rooms 401–420 where accessible
People askedCharge nurse (name), unit manager by email
Records checkedNo open repair; no OEM shipment; no loaner swap on file
Search time25 minutes (bill it if your contract allows)
OutcomeNot found; second pass scheduled Nov 10, night shift

Report it honestly

Give the customer three numbers, not one: PMs performed, PMs not performed with a documented reason (unable to locate, in use and unavailable, out for repair, failed and tagged out), and PMs simply missed. Blending them into one "completion" figure hides the third group, which is the one a surveyor will find. Separately, track how many hours your technicians spend looking for equipment. If it is significant, it belongs in your next contract price (see how to price a biomed service contract).

Stop it happening next cycle

  • Fix the inventory at the start of the contract. Walk the site and reconcile before the first PM cycle (use the medical equipment inventory template).
  • Record location changes when you see them. If a pump listed on 4 West is found on 6 East, update the location on the spot, not at month end.
  • Schedule sweeps when the equipment is there. Night shift for ward equipment, between cases for OR equipment.
  • Agree a retirement rule. For example, two consecutive unlocated cycles trigger a written request to retire or confirm.

How Bravio helps

In Bravio every device has one record with its facility, department and location, so a technician who finds a device elsewhere updates the location from the phone, offline if need be. Missed PMs are listed by facility, notes and photos go on the work order, and the customer can see their own PM schedule and reports through a read-only login. See medical equipment PM software and biomed repair shop software, or get started free.

Frequently asked questions

Does an unable-to-locate PM count as complete?

Some HTM leaders count a device as complete when it cannot be found after repeated, well-documented searches, but that is an interpretation, not an accreditation rule. Agree the method with each customer in writing, document every attempt as it happens, and report unlocated devices separately from PMs performed.

How many times should a biomed technician search for a missing device?

At least twice, on different days and ideally different shifts, plus a written request to the department and the customer contact. Record the date, places checked, people asked and records checked on each attempt.

Who decides to remove a missing device from the inventory?

The customer. The equipment belongs to the hospital or clinic, so the service company asks in writing and records the customer’s decision to retire the device or keep it on the inventory.

Can a service company bill for time spent searching for equipment?

Only if the contract allows it. Many contracts do not, which is why search time should be tracked and priced into the next contract renewal.

One place to run
your biomed repair shop.

Sign up and you’re in. We move your data over, free. No card.

See how we work →